Category: free videos

New Clips and Preview/Teaser

      Comments Off on New Clips and Preview/Teaser

I have three new clips available. The new clips are “Stretched Out“, “Hold Those Legs Up“, and “Bound for Torment“. Click on the name of the clip to view it in the clip store.

In “Stretched Out”, John’s balls are tugged up from behind when he pulls down on his wrists. His ankles are chained.

In “Hold Those Legs Up”, his ankles are tied to the rope around his genitals so he cannot lower his ankles without tugging on his balls. I this one, John is wearing tiny, tight jean shorts that make the harness on his cock & balls even more painful. This video might also be a favorite among foot fetishists, as it has lots of closeups of John’s dirty, bare, bound feet.

John is naked in “Bound for Torment”, and he is tethered by his genitals to a square post in a most unforgiving and vulnerable position. The second half of the video finds John still tethered but with enough freedom of movement that he can masturbate himself to orgasm.

In the first two videos, John is gagged with a strict, mouth-filling panel gag. In the last video, he is gagged with a red ball gag that is pulled tight into his mouth and locked on so he cannot push it out or remove it.

New Clip: Cuffed & Drooling in Blue PVC

      Comments Off on New Clip: Cuffed & Drooling in Blue PVC

I really enjoyed shooting this video and it came out pretty good, visually. I was a little disappointed in the auto focus “hunting” every so often, but it mostly got the focus right, which is hard for me to do manually. The real disappointment was the audio. Apparently the microphone battery was low, so there is a very noticeable noise level in the audio that partially obscures the subject and is generally annoying. I uploaded the clip to PornHub anyway, because it is a pretty hot clip.

The main scene in the clip features me, gagged and locked into three pairs of steel cuffs. One pair locks my wrists around a small tree in front of me, another pair is around my ankles and another tree behind me, and the final pair is around my genitals and the tree behind me. The cuff around my genitals holds me to the tree and discourages me from struggling, but I still struggle a lot. The ankle cuffs are really just there in case I rip my genitals off. In that case, I’ll still be locked between two trees with no hope of escape.

By the end of the main scene, I’m very horny and I’m drooling all over myself, so I setup and shoot a little more video where I’m cuffed to another tree and my arms are cuffed behind me. I get some more, sexy camera angles and some great shots of the drool that is now streaming uncontrollably down my chest.

I also included a couple closeups of the PVC shorts without the handcuffs just because I think they are sexy as hell. You can find the video in high definition on PornHub at this link.

Shooting Solo is Challenging

      Comments Off on Shooting Solo is Challenging

For those of you who don’t already know, I shoot at least half of my content solo. That means getting myself in and out of the bondage, but also setting up multiple cameras to capture multiple, simultaneous camera angles. I shoot with 2-4 cameras. More often than not, at least one camera doesn’t get what I wanted. I generally prefocus the cameras, and of course I have to frame the shot using mostly my imagination because I can’t be tied up in the shot until all of the cameras are setup and rolling.

This weekend, I revisited an old idea to retrofit a linear actuator on my jib and figure out how to preprogram it to move the camera to get body pans and closeups at various levels. In the past, I’d gotten stuck on how to programmatically determine the position of the jib arm. I could find no way to affix a potentiometer that would measure the angle of the arm, and timing the up/down motion seemed too imprecise. I finally thought of a reliable way to determine the vertical position of the camera, so I set about attaching the actuator and wiring the actuator controls to an Arduino. I hooked up an old joystick that I could use to move the actuator arm and program the desired stops into the Arduino memory.

I needed to have designated stops because the actuator makes too much noise to just let it pan up and down. I programmed the system to move from stop to stop and pause for 40 seconds to get some video without motor noise from the actuator. For the most part, the experiment was a success, but I really need to start from scratch, building a jib arm that is designed for multi-axis computer control. I could go on for paragraphs about the features I’d like to build into my automated camera operator, but let’s have a look at an edited video from today’s test shot.

I prefocused the camera for this video test and I didn’t quite get it right. If I had used the camera’s autofocus, it may have decided to focus on the background half way through and I would have had an unusable clip. Although this was a quick test, it was still a lot of work, setting up equipment, chaining myself to a post, and trying not to gag on the really strict gag while struggling and waiting for the camera to run through it’s cycles. I didn’t do a great job editing it, but I think it came out alright, considering that I was using only one camera and there was no camera operator. If I had done this for a real clip, there would be at least one other camera to get a wider shot, and possibly a nice side shot. I hope you enjoy the free video.

I think my next challenge will be to fix the noise problem. I really like the shots where the camera is slowly panning over the body.